This dataset is the result of an experimental series that was carried out in September/October 2022 at GFZ German Research Centre for Geosciences, Potsdam, Germany to observe biosorption of lead under extreme conditions. Synthetic solutions, simulating the geothermal fluids from the Heemskerk geothermal power plant were were prepared in 30 ml glass vials (Rotalibo screw neck ND24 EPA). To prepare the stock solutions, sodium chloride (NaCl, 99.8 %, Cellpure, Merck, DE) was added at 265 g/L and Pb(II), in form of lead nitrate (Pb(NO3 )2 , Merck, DE), at 1 g/L to ultrapure water. To assess the impact of acetic acid on lead biosorption, two treatments were done: one without acetic acid and one where acetic acid (100 %, Merck, DE) was added at 60 mg/L. Finally, dead biomass of the fungus Penicillium citrinum was added in the samples at a concentration of 4 g/L (Wahab et al., 2017). The samples were incubated in an autoclave at a pressure of 8 bars on a rotative shaker. The temperature was set at 25 °C, 60 °C or 98 °C with three contact times (1, 2 and 3 h). All treatments were performed in triplicates. For each treatment, two controls without biomass were done. Control samples without the addition of NaCl were done in duplicate, at 25 °C and for 2 h. After incubation, samples were filtered through a 0.22 µm nitrocellulose filter (Sartorius Stedim Biotech, FR) to separate the biomass from the liquid. The biomass on the filters was dried for 24 h at 45 °C before being scraped from the filter and kept in a Falcon tube at room temperature.
Strokkur is a pool geyser in southwest Iceland that erupts every 3.7 minutes. Eruptions start with a blue water bulge that soon turns white (bulge phase) before the water bubble bursts into a jetting water fountain (jet phase). We measured the bulge rising velocity and height and fountain rising velocity and height using video cameras and drones from GFZ and the accompanying ground motion using seismometers from the University of Potsdam. We publish the derived products from video data and seismic data here.
The main objective of the work package 2 of the REFLECT project is to characterise relevant fluid properties and their reactions for saline fluids (type C). One of the specific goals was to collect fluid samples from several saline fluids from geothermal sites across Europe, determine their properties, and thus contribute to the Fluid Atlas (WP3). Additionally, the REFLECT team will compare those field data with data from lab experiments performed at near natural conditions. Samples of type C fluids were taken from several sites in Germany, Austria, Belgium and the Netherlands. The samples were analysed for major and minor ions, dissolved gases and isotopes. At the geothermal site Blumau in Austria five thermal water samples were taken by Hydroisotop at the production and injection well, as well as after the heat exchanger on 29th of June 2020. Besides the hydrochemical composition, dissolved gases, the heavy metal content, DOC and stable isotopes (18O, 2H, 13C-DIC) were analysed. Additionally, three thermal water samples were taken by the operator on 09th of March 2021 and sent to Hydroisotop for DOC measurements. The dataset contains analysis results associated with the research project reflect. It is a comma separated file (csv) containing the following columns: Location,Country,Description,Laboratory,Lab No.,Sampling date,Temperature at sampling (degC),Spec. electr. conductivity (25 degC) at sampling,Spec. electr. conductivity (25 degC) Lab. (muS/cm),pH value at sampling,pH value Lab.,Temperature Lab. (degC),Dissolved oxygen content (mg/l),Redox potential (mV),Alkalinity (pH 4.3) Lab. (mmol/l),Sodium (mg/l),Potassium (mg/l),Calcium (mg/l),Magnesium (mg/l),Ammonium (mg/l),Hydrogen carbonate (mg/l),Chloride (mg/l),Sulphate (mg/l),Nitrate (mg/l),Nitrite (mg/l),Antimony (mg/l),Barium (mg/l),Boron (mg/l),Bromide (mg/l),Fluoride (mg/l),Iodide (mg/l),Molybdenum (mg/l),Ortho-phosphate (mg/l),Selenium (mg/l),Strontium (mg/l),Sulphide total (mg/l),Aluminium (mg/l),Arsenic (mg/l),Lead (mg/l),Cadmium (mg/l),Chromium total (mg/l),Cobalt (mg/l),Iron total (mg/l),Copper (mg/l),Nickel (mg/l),Mercury (mg/l),Zinc (mg/l),Tin (mg/l),DOC (mg/l),Hydrogen (Nml/kg),Oxygen (Nml/kg),Nitrogen (Nml/kg),Carbon dioxide (Nml/kg),Methane (Nml/kg),Ethane (Nml/kg),Propane (Nml/kg),Butane (Nml/kg),Pentane (Nml/kg),Ethene (Nml/kg),Propene (Nml/kg),Helium (Nml/kg),Argon (Nml/kg),Sum Gases (Nml/kg),Oxygen-18 d18O-H2O (per mille VSMOW),Deuterium d2H-H2O (per mille VSMOW),Deuterium-excess (per mille VSMOW),Carbon-13 d13C-DIC (per mille VPDB) Methods are described in the accompanying deliverable Fluid data of geothermal sites (type C).
The main objective of the work package 2 of the REFLECT project is to characterise relevant fluid properties and their reactions for saline fluids (type C). One of the specific goals was to collect fluid samples from several saline fluids from geothermal sites across Europe, determine their properties, and thus contribute to the Fluid Atlas (WP3). Additionally, the REFLECT team will compare those field data with data from lab experiments performed at near natural conditions. Samples of type C fluids were taken from several sites in Germany, Austria, Belgium and the Netherlands. The samples were analysed for major and minor ions, dissolved gases and isotopes. Two thermal water samples were taken by Hydroisotop at the production and injection wells in Insheim on 18th of June 2020. The samples were analysed for their hydrochemical composition, heavy metal and dissolved organic carbon (DOC) content, dissolved gases and stable isotopes of water and gas components (18O, 2H, 34S-H2S, 34S-SO4, 18O-SO4, 13C-DIC, 13C-CO2, 13C-CH4, 2H-CH4). Nitrate and a positive redox potential is present in both water samples when reducing conditions would be expected in a deep geothermal well. On-site measurements showed no oxygen present. It is however possible that air contamination during sampling caused some ammonium to oxidize to nitrate. The dataset contains analysis results associated with the research project REFLECT. It is a comma separated file (csv) containing the following columns: Location,Country,Description,Laboratory (Lab.),Lab. No.,Sampling date,Temperature at sampling (degC),Spec. electr. conductivity (25 degC) at sampling (muS/cm),Spec. electr. conductivity (25 degC) Lab. (muS/cm),pH value at sampling,pH value Lab.,Dissolved oxygen content (mg/l),Redox potential (mV),Base capacity (pH 8.2) (mmol/l),Alkalinity (pH 4.3) on site (mmol/l),Alkalinity (pH 4.3) Lab. (mmol/l),Sodium (mg/l),Potassium (mg/l),Calcium (mg/l),Magnesium (mg/l),Ammonium (mg/l),Hydrogen carbonate (mg/l),Chloride (mg/l),Sulphate (mg/l),Nitrate (mg/l),Antimony (mg/l),Barium (mg/l),Bromide (mg/l),Fluoride (mg/l),Iodide (mg/l),Lithium (mg/l),Molybdenum (mg/l),Total phosphate (mg/l),Ortho-phosphate (mg/l),Silicon (mg/l),Strontium (mg/l),Sulphide total (mg/l),Aluminium (mg/l),Arsenic (mg/l),Lead (mg/l),Iron total (mg/l),Copper (mg/l),Manganese total (mg/l),Nickel (mg/l),Uranium (mg/l),Zinc (mg/l),DOC (mg/l),Hydrogen (Nml/kg),Oxygen (Nml/kg),Nitrogen (Nml/kg),Carbon dioxide (Nml/kg),Methane (Nml/kg),Ethane (Nml/kg),Propane (Nml/kg),Butane (Nml/kg),Pentane (Nml/kg),Helium (Nml/kg),Argon (Nml/kg),Sum Gases (Nml/kg),Oxygen-18 d18O-H2O (per mille VSMOW),Deuterium d2H-H2O (per mille VSMOW),Deuterium-excess (per mille VSMOW),Carbon-13 d13C-DIC (per mille VPDB),Sulphur-34 d34S-SO4 (per mille V-CDT),Sulphur-34 d34S-H2S (per mille V-CDT),Oxygen-18 d18O-SO4 (per mille VSMOW),Carbon-13 d13C-CO2 (per mille VPDB),Carbon-13 d13C-CH4 (per mille VPDB),Deuterium d2H-CH4 (per mille VPDB). Methods are described in the accompanying deliverable Fluid data of geothermal sites (type C)
The main objective of the work package 2 of the REFLECT project is to characterise relevant fluid properties and their reactions for saline fluids (type C). One of the specific goals was to collect fluid samples from several saline fluids from geothermal sites across Europe, determine their properties, and thus contribute to the Fluid Atlas (WP3). Additionally, the REFLECT team will compare those field data with data from lab experiments performed at near natural conditions. Samples of type C fluids were taken from several sites in Germany, Austria, Belgium and the Netherlands. The samples were analysed for major and minor ions, dissolved gases and isotopes. One sample of thermal water was taken from the production well at Balmatt, Belgium on May 17th 2021 and sent to Hydroisotop for analysis of main cations and anions and heavy metals. It can be seen that the nitrate content is remarkably high. However, all meaurements had to be conducted from the same sample bottle, which had been acidified, presumably with HNO3 which can be expected to be the source of the high nitrate content. The dataset contains analysis results associated with the research project REFLECT. It is a comma separated file (csv) containing the following columns: Location,Country,Description,Laboratory (Lab.),Lab. No.,Sampling date,Sodium (mg/l),Potassium (mg/l),Calcium (mg/l),Magnesium (mg/l),Chloride (mg/l),Sulphate (mg/l),Nitrate (mg/l),Antimony (mg/l),Barium (mg/l),Iodide (mg/l),Lithium (mg/l),Silicon (mg/l),Strontium (mg/l),Aluminium (mg/l),Arsenic (mg/l),Lead (mg/l),Iron total (mg/l),Copper (mg/l),Manganese total (mg/l),Nickel (mg/l),Uranium (mg/l),Zinc (mg/l) Methods are described in the accompanying deliverable Fluid data of geothermal sites (type C).
The main objective of the work package 2 of the REFLECT project is to characterise relevant fluid properties and their reactions for saline fluids (type C). One of the specific goals was to collect fluid samples from several saline fluids from geothermal sites across Europe, determine their properties, and thus contribute to the Fluid Atlas (WP3). Additionally, the REFLECT team will compare those field data with data from lab experiments performed at near natural conditions. Samples of type C fluids were taken from several sites in Germany, Austria, Belgium and the Netherlands. The samples were analysed for major and minor ions, dissolved gases and isotopes. In order to gain information about the increased methane content (about 65 vol-%) in the gas samples of the Groß Schönebeck production well (GrSk05/05) collected in February 2021 as compared to previous samples in 2010-2018 (10-14 vol-%), three gas samples were sampled by GFZ on 02 March 2021 at the valve at the wellhead when releasing the pressure from the wellhead. Main gas composition was measured by GFZ indicating again predominantly CH4 (63,9-64,2 Vol-%) followed by N2 (30,9 – 31,2 vol.-%) with minor amounts of H2 (3,4 vol-%) and CO2 (0,01-0,04 vol-%). Potential reasons for the increased methane content could be either microbial activity or contribution of fluid / gas from a different source within the reservoir. To determine the origin of methane, therefore, isotope analyses were performed. The samples arrived at Hydroisotop on March 13th 2021 for the analysis of higher hydrocarbons (C2-C5) and their isotopic composition (13C-CO2, 13C -CH4, 13C-CxHy and 2H-CH4). Together with the measured high amounts of higher hydrocarbons (ethane, propane etc.) they indicate a rather thermogenic source of the hydrocarbons. To better clarify the question of the source of methane, additionally, two downhole water samples from two different depths (1500 and 4000 m) were taken by GFZ on 09th and 10th of June 2021 and sent to Hydroisotop for analysis of main cations and anions, heavy metals, trace elements and isotopes (13C-CH4) in July 2021. The water sample composition resembles those of earlier measurements of samples collected in Groß Schönebeck (e.g. Regenspurg et al., 2010). However, since the well had not been in operation for a while a depth differentiation between the sample from 4000 m and the one from 1500 m is obvious. This was already visible by the black precipitate observed in the 4000 m sample, whereas the sample at 1500 m showed da reddish precipitate of presumably iron oxides. It should be noted that the nitrate content of the water samples is unusually high since reducing conditions are expected. This could have been caused by air contact of the sample and subsequent oxidation. Furthermore, a reduced silicon content shows in sample 365871 compared to sample 365870. Given the high temperature of the well, the higher silicon content is more plausible. The dataset contains analysis results associated with the research project REFLECT. It is a comma separated file (csv) containing the following columns: Location,Country,Description,Laboratory (Lab.),Lab. No.,Sampling date,Sodium (mg/l),Potassium (mg/l),Calcium (mg/l),Magnesium (mg/l),Chloride (mg/l),Sulphate (mg/l),Nitrate (mg/l),Antimony (mg/l),Barium (mg/l),Bromide (mg/l),Fluoride (mg/l),Iodide (mg/l),Lithium (mg/l),Silicon (mg/l),Strontium (mg/l),Aluminium (mg/l),Arsenic (mg/l),Lead (mg/l),Copper (mg/l),Manganese total (mg/l),Nickel (mg/l),Uranium (mg/l),Zinc (mg/l),Ethane (vpm),Propane (vpm),i-Butane (vpm),n-Butane (vpm),i-Pentane (vpm),n-Pentane (vpm),Ethene (vpm),Propene (vpm),1-Butene (vpm),Carbon-13 d13C-CO2 (per mille VPDB),Carbon-13 d13C-CH4 (per mille VPDB),Deuterium d2H-CH4 (per mille VPDB),Carbon-13 d13C-C2H6 (per mille VPDB),Carbon-13 d13C-C3H8 (per mille VPDB),Carbon-13 d13C-i-C4H10 (per mille VPDB),Carbon-13 d13C-n-C4H10 (per mille VPDB) Methods are described in the accompanying deliverable Fluid data of geothermal sites (type C).
The main objective of the work package 2 of the REFLECT project is to characterise relevant fluid properties and their reactions for saline fluids (type C). One of the specific goals was to collect fluid samples from several saline fluids from geothermal sites across Europe, determine their properties, and thus contribute to the Fluid Atlas (WP3). Additionally, the REFLECT team will compare those field data with data from lab experiments performed at near natural conditions. Samples of type C fluids were taken from several sites in Germany, Austria, Belgium and the Netherlands. The samples were analysed for major and minor ions, dissolved gases and isotopes. On 29th and 30th of April 2021 five thermal water samples were taken by Hydroisotop from five different springs/wells located at Wildbad-Einöd. The samples were analysed for hydrochemical composition, heavy metals and dissolved organic carbon (DOC) content. It can be noted that the bromide content of sample 361625 is much lower than the bromide content in the other four springs. Since the chloride content in all springs is the same order of magnitude and Cl/Br ratios are expected to be similar in the same The dataset contains analysis results associated with the research project REFLECT. It is a comma separated file (csv) containing the following columns: Location,Country,Description,Laboratory (Lab.),Lab. No.,Sampling date,Temperature at sampling (degC),Spec. electr. conductivity (25 degC) at sampling (muS/cm),Spec. electr. conductivity (25 degC) Lab. (muS/cm),pH value at sampling,pH value Lab.,Temperature Lab. (degC),Dissolved oxygen content (mg/l),Redox potential (mV),Base capacity (pH 8.2) (mmol/l),Alkalinity (pH 4.3) on site (mmol/l),Alkalinity (pH 4.3) Lab. (mmol/l),Sodium (mg/l),Potassium (mg/l),Calcium (mg/l),Magnesium (mg/l),Ammonium (mg/l),Hydrogen carbonate (mg/l),Chloride (mg/l),Sulphate (mg/l),Nitrate (mg/l),Nitrite (mg/l),Bromide (mg/l),Fluoride (mg/l),Iodide (mg/l),Lithium (mg/l),Silicon (mg/l),Strontium (mg/l),Iron total (mg/l),Manganese total (mg/l),DOC (mg/l) Methods are described in the accompanying deliverable Fluid data of geothermal sites (type C)
The main objective of the work package 2 of the REFLECT project is to characterise relevant fluid properties and their reactions for saline fluids (type C). One of the specific goals was to collect fluid samples from several saline fluids from geothermal sites across Europe, determine their properties, and thus contribute to the Fluid Atlas (WP3). Additionally, the REFLECT team will compare those field data with data from lab experiments performed at near natural conditions. Samples of type C fluids were taken from several sites in Germany, Austria, Belgium and the Netherlands. The samples were analysed for major and minor ions, dissolved gases and isotopes. On 10th of May 2021, two thermal water samples were taken by TNO before and after the heat exchanger at the geothermal site Heemskerk in the Netherlands. The samples sent to Hydroisotop were analysed for their hydrochemical composition, heavy metal and dissolved organic carbon (DOC) content and stable isotopes (18O, 2H, 13C-DIC). It should be noted that the pH measured in the laboratory diverges from previously observed pH values which in the past have not been reported below 5,4. Concentrations of major ions had initially been reported too low but re-measurement of the samples yielded values in ranges that had previously been recorded. However, the concentraton of Lithium is much higher than expected. In order to resolve these uncertainties, the site Heemskerk will be sampled again. The dataset contains analysis results associated with the research project REFLECT. It is a comma separated file (csv) containing the following columns: Location,Country,Description,Laboratory (Lab.),Lab. No.,Sampling date,Spec. electr. conductivity (25 degC) Lab. (muS/cm),pH value Lab.,Temperature Lab. (degC),Alkalinity (pH 4.3) Lab. (mmol/l),Sodium (mg/l),Potassium (mg/l),Calcium (mg/l),Magnesium (mg/l),Ammonium (mg/l),Hydrogen carbonate (mg/l),Chloride (mg/l),Sulphate (mg/l),Nitrate (mg/l),Antimony (mg/l),Barium (mg/l),Fluoride (mg/l),Iodide (mg/l),Lithium (mg/l),Silicon (mg/l),Strontium (mg/l),Aluminium (mg/l),Arsenic (mg/l),Lead (mg/l),Iron total (mg/l),Copper (mg/l),Manganese total (mg/l),Nickel (mg/l),Uranium (mg/l),Zinc (mg/l),DOC (mg/l),Oxygen-18 d18O-H2O (per mille VSMOW),Deuterium d2H-H2O (per mille VSMOW),Deuterium-excess (per mille VSMOW),Carbon-13 d13C-DIC (per mille VPDB). Methods are described in the accompanying deliverable Fluid data of geothermal sites (type C)
The main objective of the work package 2 of the REFLECT project is to characterise relevant fluid properties and their reactions for saline fluids (type C). One of the specific goals was to collect fluid samples from several saline fluids from geothermal sites across Europe, determine their properties, and thus contribute to the Fluid Atlas (WP3). Additionally, the REFLECT team will compare those field data with data from lab experiments performed at near natural conditions. Samples of type C fluids were taken from several sites in Germany, Austria, Belgium and the Netherlands. The samples were analysed for major and minor ions, dissolved gases and isotopes. At Neustadt-Glewe one thermal water sample was taken by GFZ on June 02, 2021 and sent to Hydroisotop for analysis of main cations, anions, heavy metals, DOC, gases and isotopes (18O, 2H, 18O-SO4, 2H, 13C-DIC, 13C-CO2, 13C-CH4, 13C-CxHy, 2H-CH4, 34S-SO4, 34S-H2S, 2H-CH4). There was too little H2S in sample 363469 to conduct the 34S-H2S measurement. The dataset contains analysis results associated with the research project REFLECT. It is a comma separated file (csv) containing the following columns: Location,Country,Description,Laboratory (Lab.),Lab. No.,Sampling date,Spec. electr. conductivity (25 degC) Lab.,pH value Lab.,Temperature Lab. (degC),Alkalinity (pH 4.3) Lab. (mmol/l),Sodium (mg/l),Potassium (mg/l),Calcium (mg/l),Magnesium (mg/l),Ammonium (mg/l),Hydrogen carbonate (mg/l),Chloride (mg/l),Sulphate (mg/l),Nitrate (mg/l),Antimony (mg/l),Barium (mg/l),Fluoride (mg/l),Iodide (mg/l),Lithium (mg/l),Silicon (mg/l),Strontium (mg/l),Aluminium (mg/l),Arsenic (mg/l),Lead (mg/l),Chromium total (mg/l),Iron total (mg/l),Copper (mg/l),Manganese total (mg/l),Nickel (mg/l),Uranium (mg/l),Zinc (mg/l),DOC (mg/l),Hydrogen (Nml/kg),Oxygen (Nml/kg),Nitrogen (Nml/kg),Carbon dioxide (Nml/kg),Methane (Nml/kg),Ethane (Nml/kg),Propane (Nml/kg),Butane (Nml/kg),Pentane (Nml/kg),Helium (Nml/kg),Argon (Nml/kg),Sum Gases (Nml/kg),Oxygen-18 d18O-H2O (per mille VSMOW),Deuterium d2H-H2O (per mille VSMOW),Deuterium-excess (per mille VSMOW),Carbon-13 d13C-DIC (per mille VPDB),Sulphur-34 d34S-SO4 (per mille V-CDT),Oxygen-18 d18O-SO4 (per mille VSMOW),Carbon-13 d13C-CO2 (per mille VPDB),Carbon-13 d13C-CH4 (per mille VPDB),Deuterium d2H-CH4 (per mille VSMPW),Carbon-13 d13C-C2H6 (per mille VPDB),Carbon-13 d13C-C3H8 (per mille VPDB),Carbon-13 d13C-i-C4H10 (per mille VPDB),Carbon-13 d13C-n-C4H10 (per mille VPDB) Methods are described in the accompanying deliverable Fluid data of geothermal sites (type C) .
| Origin | Count |
|---|---|
| Wissenschaft | 9 |
| Type | Count |
|---|---|
| unbekannt | 9 |
| License | Count |
|---|---|
| offen | 9 |
| Language | Count |
|---|---|
| Englisch | 9 |
| Resource type | Count |
|---|---|
| Keine | 9 |
| Topic | Count |
|---|---|
| Boden | 5 |
| Lebewesen & Lebensräume | 8 |
| Luft | 6 |
| Mensch & Umwelt | 9 |
| Wasser | 9 |
| Weitere | 9 |