Other language confidence: 0.9498996553449545
This data set includes digital image correlation data from analog earthquakes experiments. The data consists of grids of surface strain and time series of surface displacement (horizontal and vertical) and strain. The data have been derived using a stereo camera setup and processed with LaVision Davis 10 software. Detailed descriptions of the experiments and results regarding the surface pattern of the strain can be found in Kosari et al. (2022), to which this data set is supplementary. We use an analog seismotectonic scale model approach (Rosenau et al., 2019 and 2017) to generate a catalog of analog megathrust earthquakes (Table 1). The presented experimental setup is modified from the 3D setup used in Rosenau et al. (2019) and Kosari et al. ( 2020). The subduction forearc model wedge is set up in a glass-sided box (1000 mm across strike, 800mm along strike, and 300 mm deep) with a dipping, elastic basal conveyor belt and a rigid backwall. An elastoplastic sand-rubber mixture (50 vol.% quartz sandG12: 50 vol.% EPDM rubber) is sieved into the setup representing a 240 km long forearc segment from the trench to the volcanic arc. The shallow part of the wedge includes a basal layer of sticky rice grains characterized by unstable stick-slip sliding representing the seismogenic zone. Stick-slip sliding in rice is governed by a rate-and-state dependent friction law similar to natural rocks. According to Coulomb wedge theory (Dahlen et al., 1984), two types of wedge configurations have been designed: a “compressional” configuration represents an interseismically compressional and coseismically stable wedge (compressional configuration), and a “critical” configuration, which is interseismically stable (close to critically compressional) and may reach a critical extensional state coseismically (critical configuration). In the compressional configuration, a flat-top (surface slope α=0) wedge overlies a single large rectangular in map view stick-slip patch (Width*Length=200*800 mm) over a 15-degree dipping basal thrust. In the critical configuration, the surface angle of the elastoplastic wedge varies from the coastal segment onshore (α=10) to the inner-wedge offshore (α=15) segments over a 5-degree dipping basal thrust. Slow continuous compression of the wedge by moving the basal conveyor belt at a speed velocity of 0.05 mm/s simulates plate convergence and results in the quasi-periodic nucleation of quasi-periodic stick-slip events (analog earthquakes) within the rice layer. The wedge responds elastically to these basal slip events, similar to crustal rebound during natural subduction megathrust earthquakes.
This data set includes data derived from high-speed surface displacement observations from analog earthquake experiments. The data consists of surface displacement of the experiment upper plate and slab, slip distribution, and grids of Coulomb Failure Stress (CFS). The surface displacement observations have been captured using a highspeed CMOS (Complementary Metal Oxide Semiconductor) camera (Phantom VEO 640L camera, 12 bit) and processed with LaVision Davis 10 software. Description of the experiments and results regarding the surface displacement observation, Slip distribution, and CFS can be found in Kosari et al. (2022), to which this data set is supplementary. We use an analog seismotectonic scale model approach (Rosenau et al., 2019 and 2017) to generate a catalog of analog megathrust earthquakes. The presented experimental setup is modified from the 3D setup used in Rosenau et al. (2019) and Kosari et al. ( 2020 and 2022). The subduction forearc model wedge is set up in a glass-sided box (1000 mm across strike, 800mm along strike, and 300 mm deep) with a dipping, elastic basal conveyor belt, and a rigid backwall. An elastoplastic sand-rubber mixture (50 vol.% quartz sandG12: 50 vol.% EPDM rubber) is sieved into the setup representing a 240 km long forearc segment from the trench to the volcanic arc. The shallow part of the wedge includes a basal layer of sticky rice grains characterized by unstable stick-slip sliding representing the seismogenic zone. The Stick-slip sliding in rice is governed by a rate-and-state dependent friction law similar to natural rocks. A flat-top (surface slope α=0) wedge overlies rectangular stick-slip patch/es over a 15-degree dipping basal thrust. Two different seismic configurations of the shallow part of the wedge base (the megathrust) represent the depth extent of the seismogenic zone in nature. In the first configuration (homogeneous configuration), a single large rectangular stick-slip patch (Width*Length=200*800 mm) is implemented as the main slip patch (MSP). In the second case (heterogeneous configuration), two square-shaped MSPs (200*200mm) have been emplaced, acting as two medium-size seismogenic asperities surrounded by a salt matrix hosting frequent small events. Slow continuous compression of the wedge by moving the basal conveyor belt at a speed velocity of 0.05 mm/s simulates plate convergence and results in the quasi-periodic nucleation of quasi-periodic stick-slip events (analog earthquakes) within the sticky-rice layer. The wedge responds elastically to these basal slip events, similar to crustal rebound during natural subduction megathrust earthquakes.
This dataset includes video sequences depicting the evolution in map view and lateral view of 7 analogue experiments studying mantle-scale subduction systems. The experiments are performed under a natural gravity field and are designed to understand the role of convergence obliquity on upper plate deformation and partitioning, with a particular emphasis on the role played by lithospheric inherited structures on the development of sliver tectonics. All experiments were performed at the Laboratory of Tectonic modelling of the University of Rennes 1 (France). The experimental set-up corresponds to a lithosphere and sub-lithospheric upper mantle system. The lithospheric plates are simulated with PDMS silicone (Polydimethylsiloxane Silicone) with different viscosities and densities, and the upper mantle with glucose syrup. In particular, for the overriding plate, we simulate the presence of a weaker volcanic arc that can eventually be decoupled from the forearc by a pre-existing discontinuity. The materials are placed into a Plexiglas tank, where the impermeable bottom of the tank represents the 660 km discontinuity. The subduction is initiated by manually forcing the slab into the mantle and it then evolves under the combined effects of internal buoyancy forces (slab pull) and external boundary forces. The subducting plate is pushed toward the trench at a constant velocity of 1.5 cm/min while the overriding plate is maintained fixed during the duration of the experiments. The evolution of the experiments is monitored by DSLR cameras (24 Mpx) taking pictures every 30 seconds at the top and on one side of the experiments. Pictures are then assembled into video-sequences. The scale bar, with black & white rectangles corresponds to 10 cm. The set of experiments consists of one reference model (MODEL-01) with orthogonal convergence, and six models with oblique convergence (Table 1). Among these models, three do not embed a pre-existing lithospheric discontinuity in the overriding plate (MODEL-02, MODEL-03, and MODEL-04) while the three other (MODEL-05, MODEL-06, and MODEL-07) have such a discontinuity. For the models with oblique convergence, we vary the angle between the convergence direction and the trench from 80° (MODEL-02 and MODEL-05) to 60° (MODEL-03 and MODEL-06) and 50° (MODEL-04 and MODEL-07). For details on the experimental set-up, and interpretation of the results, please refer to Suárez et al. (submitted to Tectonophysics) to which these data are supplementary material.
This dataset provides friction and elasticity data from ring shear and axial tests, respectively, on rock analogue materials used at the University Roma Tre (Rome, IT) in “Foamquake”, a novel seismotectonic analog model mimicking the megathrust seismic cycle (Mastella et al., under review). Two granular materials (quartz sand and Jasmine rice) have been characterized by means of internal friction coefficients µ and cohesions C. An elastic material (foam rubber) have been characterized by means of Young’s modulus E and Poisson’s ratio v. According to our analysis the granular materials show Mohr-Coulomb behaviour characterized by linear failure envelopes in the shear stress vs. normal load Mohr space. Peak, dynamic and reactivation friction coefficients of the quartz sand are µP = 0.69, µD = 0.56 and µR = 0.64, respectively. Cohesion ranges between 50 and 100 Pa. Rate-dependency of friction in quartz sand seems insignificant. Peak, dynamic and reactivation friction coefficients of the Jasmine rice are µP = 0.70, µD = 0.59 and µR = 0.61, respectively. Cohesion ranges between 30 and 50 Pa. Rate-weakening of Jasmine rice is c. 6% per tenfold change in shear velocity v. The Young’s modulus of the foam rubber has been constrained to 30 kPa, its Poisson’s ratio is v=0.1.
This dataset includes images depicting the evolution in map view and lateral view of 7 analogue experiments of subduction to better understand the interplays between slab pull and mantle flow at subduction zones. The experiments are performed under a natural gravity field and are designed to understand the influence of plate width and magnitude and direction of mantle flow on slab geometry, trench kinematics and shape, and superficial mantle deformation around the subduction zone. All experiments were performed at the Laboratory of Experimental Tectonics at the Università Roma Tre (Italy). The laboratory models consist of one viscous layer of silicone putty representing the subducting lithosphere resting on top of a tank filled with glucose syrup, representing the convective mantle. We impose a horizontal flow in the convective mantle by pushing at a constant velocity a piston in the glucose syrup below an intermediate horizontal plate representing the upper mantle-lower mantle discontinuity. The pictures show the time evolution of each experiment from the top (« top » folder) and lateral position (« lateral » folder) and were taken synchronously every 30 seconds, and downsampled to 5 minutes in this dataset. The entire set of pictures are available from the authors upon request. Model F14 is the reference model, without imposed mantle flow and with a slab width of 2000. Models F15 and F16 are models with 660 km and 4000 km, respectively. They allow us analyzing the effect of slab width in the absence of a background flow. Models F17 and F20 are models with slab width of 2000 km and a background flow coming from above the slab at velocities of 0.9 and 1.8 mm/min in the lab (corresponding to 0.9 and 2 cm/yr once scaled to nature), respectively. Models F24 and F26 are models with slab width of 2000 km and a background flow coming from below the slab at velocities of 0.9 and 1.8 mm/min in the lab (corresponding to 1.2 and 2.7 cm/yr once scaled to nature), respectively. For details on the experimental set-up, monitoring techniques and interpretation of the results, please refer to Guillaume et al. (2021) to which these data are supplementary material.
This data set includes digital image correlation data from thirteen analogue earthquakes generated by means of an analogue seismotectonic scale model approach. The data consists of grids of 3D static coseismic surface displacements. The data have been derived using a stereo camera setup and processed with LaVision Davis 8 software. Detailed descriptions of the experiments and results regarding the control of geodetic coverage on the slip inversion problem can be found in Kosari et al. (2020) to which this data set is supplementary material. We use an analogue seismotectonic scale model approach (Rosenau et al., 2017) to generate a catalogue of analogue megathrust earthquakes (Table 1). The presented experimental setup is modified from the 3D setup used in Rosenau et al. (2019). To monitor surface deformation of the wedge analogue model a stereoscopic set of two CCD cameras (LaVision Imager pro X 11MPx, 14 bit) monitors images the wedge surface continuously at 2.5 Hz. To derive observational data similar to those from geodetic techniques, i.e. velocities at the location on the surface, we use digital image correlation (DIC, Adam et al., 2005) to derive the 3D incremental surface displacement (or velocity) at high spatial resolution (< 0.1 mm). The time series of incremental surface displacement data was calculated using LaVision Davis 8 software. The result is an evenly spaced grid of vectors per time step, oriented parallel with respect to the principal dimensions of the box.
| Organisation | Count |
|---|---|
| Wissenschaft | 6 |
| Type | Count |
|---|---|
| unbekannt | 6 |
| License | Count |
|---|---|
| Offen | 6 |
| Language | Count |
|---|---|
| Englisch | 6 |
| Resource type | Count |
|---|---|
| Keine | 6 |
| Topic | Count |
|---|---|
| Boden | 3 |
| Lebewesen und Lebensräume | 4 |
| Luft | 1 |
| Mensch und Umwelt | 6 |
| Wasser | 2 |
| Weitere | 6 |